forward

DC/DC преобразователи для платёжных шлюзов

Описание:
The PMP10110 design converts the universal input AC voltage to isolated 17V...30V@6A and is suitable to charge lead-acid or Li-Ion batteries. The converter is a constant-V and constant-I genarator and the set points for output voltage (charge level) and current are settable by means of two PWM signals. The first stage is a PFC boost while the isolation ad current stabilization is performed by DC-DC half bridge stage. An isolated quasi-resonant flyback converter supplies all internal voltages and provide some extra current for external loads (fan or analog section), in details 12V@400mA and 5V@300mA.

Возможности:

The first stage is a CCM PFC boost driven with UCC28180, showing high efficiency and low EMI signature The second stage is a DC/DC half bridge, wich includes both current and voltage loops; a PWM signal is used as reference for voltage and current An auxiliary power supply generates all needed voltages; a network is disconnecting all resistors tied to high voltage to reduce stand-by losses Plug-to-plug efficiency at full load: 86%...92% in the whole input voltage range This design is tested and includes test results and CAD files

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:

PMP10514 представляет собой высокоэффективный однофазный синхронный понижающий преобразователь, в котором использована микросхема контроллера LM25117. Проект допускает диапазон входного напряжения от 30,4 до 33,6 В (32 В номинальное значение) и выдаёт на выходе 20 В при постоянном токе нагрузки 15 А.

Возможности:

  • Высокое значение КПД (пиковое значение 97,9 %)
  • Высокая плотность мощности: 300 Вт / 9,56 квадратных дюйма
  • Программируемое ограничение тока в режиме циклического перезапуска
  • Точность опорного напряжения +/-1,5 %

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10532 reference design is an isolated Fly-Buck power supply for industrial applications. It takes 24V nominal input and provides three isolated outputs: +5V@1A and +/-15V@200mA. The design is suitable for providing isolated power supply to MCU and control circuits and positive/negative bias to Op Amps in PLC applications. The cross regulation of each output over line and load variation maintains about +/-5% tolerance, and the input voltage range of the supply is from 19V to 30V. The design features the LM5160 synchronous buck converter configured as a Fly-Buck regulator. The LM5160 has a wide Vin range of 4.5V to 65V and 1.5A output current capability with integrated switch FETs. It employs the Constant On-Time (COT) control scheme suitable for the Fly-Buck. With the benefit of primary side regulation, the Fly-Buck converter makes a compact and cost effective solution for multiple isolated output power supply without the opto-coupler feedback.

Возможности:

Three isolated outputs, +5V@1A and +/-15V@200mA, are ideal for PLC and industrial applications Fly-Buck converter design, primary side regulation Compact solution for multiple isolated output supplies 19V to 30V input voltage range, +/-5% Vout cross regulation LM5160 sync buck regulator, up to 65V wide Vin range, 1.5A capability Constant On Time control, no loop compensation and fast transient response This circuit board is tested, and the design files and test report are included.

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This synchronous buck converter design uses the TPS54623 to generate a 3.3V at 5A rail from a 4.5V-17Vdc source. The current mode control and high switching frequency of the device minimize the component count and size, resulting in a simple design. This supply achieves a peak efficiency of 96%.

Возможности:

Skips pulses to boost the efficiency at light loads Low component count and size reduces total footprint of design Peak efficiency of 96% Full design, layout, and test report

Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP10861 uses active clamp forward converter for an isolated 24V to 12V/3.4A conversion. Reverse input connection, output over-current protection, output over-voltage protection, input inrush current limiting circuit are integrated in this board. With wide 9-36V input voltage range, over 89.5% peak efficiency is achieved with 24V input voltage. All the components temperature rise are less than 30oC at full load condition.
Возможности:

24V to 12V/3.4A active clamp forward converter 9V to 36V input voltage range Integrated protections: reverse input connection, output over-current protection, output over-voltage protection Peak 89.5% efficiency with 24V iinput Test report available

Документация:
  • Схемотехника
  • BOM
Описание:
PMP20468 is an isolated flyback converter utilizing the LM5022 controller for Power-over-Ethernet applications. This design has a minimum operating input voltage of 36V, a maximum input voltage of 57V, and an output of 12V @ 2A of load current. Switching frequency is set to 420kHz. A custom Wurth transformer is used in this design.
Возможности:

36V to 57V input, 12V @ 2A output LM5022 controller for an isolated flyback topology to achieve over 89% efficiency over all operating conditions Compact size, slim form factor, suitable for power-over-ethernet camera applications Solution size: 81mm x 38mm 91% peak efficiency

Документация:
  • Схемотехника
  • BOM
Описание:

Базовый проект PMP4320A представляет собой DC/DC-преобразователь с одним выходом и полностью цифровым управлением в стандартном форм-факторе 1/2 на базе UCD3138. Он рассчитан на генерирование выходного тока до 50 А при выходном напряжении 12 В. Для данного преобразователя характерны высокие КПД и значения рабочих характеристик, а также имеется возможность гибкого конфигурирования преобразователя, что идеально подходит для использования его в качестве шинного преобразователя.

Возможности:

  • По результатам испытаний полностью соответствует требованиям клиентов на рынке телекоммуникационных систем
  • Гибкая настройка ключевых параметров
  • Полномостовой преобразователь с синхронным выпрямителем
  • Хорошие тепловые характеристики благодаря малому количеству компонентов
  • КПД 93,9 %
  • Защита от повышенного напряжения и перегрузки на выходе, а также от пониженного напряжения на входе

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This 5V / 6A solution implements a high efficiency active clamp controller LM5025A and self-drive synchronous rectifier. Input voltage is 18V-40V as typical industrial request and efficiency is 89.5%@24Vin full load. The transformer is embeded into the PCB and 8mm height can be met. The design is suitable for height limited industial applications.

Возможности:

Wide input range from 18V to 40V Adjustable Dual Mode Over-Current Protection Active Clamp Forward +S.R controller for high efficiency Lower output ripple voltage with less output capacitor Small form factor: 60mm x 40mm x 8mm Low cost through self-drive secondary synchronous rectifier circuit

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP4435 is a DC-DC isolated digital module with GaN mosfet reference design targeted for industrial and telecom applications. The DC input range is 36V-60V, with 12V typical and the output is 12V/5A. An digital controller UCD3138A is used in the design. The efficiency is up to 95.8% with good thermal performance.

Возможности:

High Efficiency up to 95.8% LM5113+ GaN Mosfets Protection feature OCP, OVP Full Digital Control for HSFB DC-DC Good thermal performance with Full Load Full comply with the telecom customer requirements

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
This is a power bank reference design with a USB typc C DFP plus a USB type A port supporting high voltage discharging. Fast charger input is also supported to save more charging time. It can detect the input port attach/detach automatically, as well as the output ports.

Возможности:

Type C DFP Enabled @5V/3A Fast Charger input supported Fast Discharging with high voltage output Automatic Attach/Detach Detection High Discharging Current High Integration and Low BOM

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

PMP6776 – недорогой неизолированный синхронный понижающий источник питания. Дизайн использует синхронные понижающие преобразователи TPS56121 и TPS54620 и понижающие переключатели TPS54425 и TPS54225 для генерирования 7 выходов. Входной диапазон питания 10,8…13,2 В, выходные напряжения 1В @ 6А, 1.5В @ 4А, 1.8В @ 6А, 2В @ 2А, 2.5В @ 8А, 3.3В @ 8А, 1.2В @ 4А.

 

Возможности:

  • Диапазон входных напряжений: 10.8…13.2В, поддержка 4,5В…14,5В;
  • Все 7 DC-DC преобразователей расположены на односторонней PCB в форм-факторе 3,5”x3,5”;
  • Дизайн отвечает требованиям по сиквенированию питания;
  • Керамические конденсаторы на входе и выходе для экономии пространства и стоимости;
  • Полностью протестированное решение

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This is a 350W High Speed Full Bridge Phase Shift ZVT Synchronous Rectification DC/DC reference design. It is built for telecom applications to supply a RF Power Amplifier stage. The design is utilizing UCC28950 voltage mode forward and average current limitation backward converter (two quadrant converter). It can modulate output voltage from 20V to 32V within 200us (at maximum 200uF of capacitive load) – so called: slow drain modulation. The converter has full load steps capability as well. It is a very small design for high sophisticated telecom applications. The system can also be used for all other two quadrant applications. Input voltage range: 36VDC-60VDC; Output voltage: 20VDC…32VDC (adjustable); Output current: 12A (18Apeak).

Возможности:

Greater than 90% efficiency at full load (24V/0.5A) Less than 80mW of stand-by power consumption under no load Constant Current regulation feature of UCC28700DBV ensures output short-circuit protection Fast Start-up

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP7328 reference design uses the TPS40422 to generate 1V at up to 60A. The design is optimized for small space while still maintaining good performance. The TPS40422 also offers PMBus control and reporting.
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Преобразователь разработан для использования в приложениях PoE класса 4, требующих высокой эффективности. Активный клампер прямоходового преобразователя с синхронным выпрямляющим диодом предоставляет высокую эффективность и малые размеры для таких приложений PoE, как беспроводные точки доступа. TPS23754 выполняет функции источника питания для PoE и ШИМ-контроллера.

Возможности:

  • Высокая эффективность (90%);
  • Выход 3,3 В при 7,6 А;
  • Изолированный прямоходовой преобразователь с синхронным выпрямителем;
  • Использует мощный высокоэффективный PoE интерфейс TPS23754;
  • PD и ШИМ-контроллер;
  • Небольшие размеры;
  • Схема протестирована и рекомендуется для новых разработок.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Преобразователь обеспечивает высокую выходную мощность 12 В/5 А для приложений PoE. PD контроллер TPS2379 допускает горячую замену внешних FET для повышения эффективности. ШИМ-контроллер UCC2897A используется для реализации активного клампера прямоходового преобразователя.

 

Возможности:

  • Высокий КПД (90% с PoE, 93,6% с адаптером питания), выход 12 В при 5 А;
  • Изолированный прямоходовой преобразователь с синхронным выпрямителем;
  • Используется TPS2379 в сочетании UCC2897A для высокой эффективности активного прямоходового преобразователя;
  • Допускает горячую замену внешнего FET для повышения эффективности;
  • Схема полностью работоспособна и рекомендована для новых разработок.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design generates a 5V/20A output from a standard 48V telecom input. The UCC2897A controls an active clamp forward converter power stage. The low gate charge and low RDSon of the CSD17312Q5, implemented as self-driven synchronous rectifiers, provide for a highly efficient design. This design is laid out in a standard 1/8th brick footprint and includes enable, remote sense, and output overvoltage features.

Возможности:

36V to 75VDC Input, 5V/20A Output (100W) Active Clamp Foward Topology Features UCC2897A Controller along with TI NexFET Synchronous Rectifiers Industry Standard Eighth Brick Footprint Output Overvoltage protection Romote Sense

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP8877 is a full-function 1/8th brick isolated DC/DC telecom power module based on the UCD3138 digital power controller. The reference design features secondary side control and hard switching full bridge power topology to deliver 12V/180W of output power operating across a wide range 36V-72V input source. The highlights of the reference design include 94% peak efficiency, fast input voltage feedforward response to input voltage surges, constant current/constant power overload protection, pre-bias start-up, current sharing control for paralleled module applications and PMBUS support for communication with peer controllers. The bias supply block employs the UCC25230, while the gate drivers used in this design include UCC27524 for driving the SR MOSFETs and UCC27211 for driving the primary side Half-Bridge MOSFETs. Other components include the ISO7240 for sending signals across the isolation barrier.

Возможности:

36-72V input, 12V/15A output 1/8th brick telecom DC/DC isolated power module Featuring Hard Switching Full Bridge power topology Secondary side control with integrated PMBUS commucation Pre-biased start-up Fast Input Voltage Feed-forward

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP8878 is a full-function 1/8th brick isolated DC/DC telecom power module based on UCC28250 advanced PWM controller. The reference design features secondary side control and hard switching full bridge power topology to deliver 12V/180W of output power operating across a wide range 40V-75V input source. The highlights of the reference design include 95% peak efficiency, pre-bias start-up, overtemperature protection and overcurrent protection (hiccup mode). The bias supply block employs the UCC25230, while the gate drivers used in this design include UCC27324 for driving the SR MOSFETs and UCC27201 for driving the primary side Half-Bridge MOSFETs.

Возможности:

40-75V input, 12V/15A output 1/8th brick telecom DC/DC isolated power module Featuring Hard Switching Full Bridge power topology Secondary side control supporting start-up under pre-bias Overcurrent protection Overtemperature protection

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP9435 is designed for industrial application for one isolated output 5V6A from input voltage of 18V to 36V, with Flyback converter of LM5022 , and a 8mm planar transformer to achieve low height.

Возможности:

Wide Vin of 6-60V Peak current mode control with inherent input voltage feed-forward Loop compensation over large output range Synchronizable to external Clock or adjustable switching frequency Low height with a 8mm planar transformer

Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Тестирование
Описание:

Высокопроизводительный индикатор тока на основе шунта используется для измерения напряжения протекающего через измерительный резистор, когда через него проходит ток. Дополнительно реализуется внешняя схема защиты от пульсаций и быстрых переходных процессов, демонстрируют различные уровни противодействия в соответствии EC61000-4-4 и IEC61000-4-5.

Возможности:

  • Способность поглощать пульсации в соответствии с требованиями IEC-61000-4;
  • Способность поглощать пульсации в соответствии с требованиями IEC-61000-5;
  • Выбор коэффициента усиления:
    • INA210: 200 V/V
    • INA211: 500 V/V
    • INA212: 1000 V/V
    • INA213: 50 V/V
    • INA214: 100 V/V
    • INA215: 75 V/V

Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы
Описание:

Данный источник питания на базе мостового LLC резонансного преобразователя с фазовым сдвигом позволяет работать с малыми нагрузками и низким выходным напряжением. Данный режим работы может заменить режим PWM в LLC, что позволяет повысить эффективность источника питания при низких нагрузках.

 

Возможности:

  • Динамическое переключение между режимами работы с фазовой и частотной модуляцией;
  • Поддержка ZVS в более широком рабочем диапазоне;
  • Управление мощностью в широком рабочем диапазоне.

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This is a high efficiency 65W AC/DC design for a Universal input (85Vac to 265Vac) to 19.5V @3.33A output exceeding CoC-5 Tier2 and DOE Level VI requirements for external power supplies using the LM5023 Quasi-Resontant Flyback Controller with UCC24630 Synchronous Rectification Controller and CSD19531Q5A MOSFET. Additionally the LM8364 reset controller is used to provide input line AC UVLO protection. As seen at APEC

Возможности:

91.49% @115V, 89.81% @230V 4-point average efficiency 83.14% @120V, 82.24% @230V 10% load efficiency 59mW No-load Power consumption 59mW at high line (230V) Fast turn-on time 75mV output ripple AC line input UVLO protection

Документация:
  • Схемотехника
  • BOM
Описание:
TIDA-00711 Design is a compact, low cost, high efficiency, dual output, 50W, isolated DC-DC converter solution designed for use in Uninterruptable Power Supplies (UPS), energy storage banks and battery powered systems that require regulated and isolated power for internal operation. This reference design is an isolated SEPIC converter implemented using the wide input, current mode controller LM5020. The design is low cost due to minimal external component count compared to standard flyback designs realized with 384x series controllers. Additionally, The design operates at high switching frequency of 300kHz, resulting in smaller magnetics and high power density solution. TIDA-00711 design has built-in protections for output overcurrent, and input under-voltage protection. The hardware is tested to meet conducted emission norm EN55011/22 Class A.
Возможности:

Designed to power a wide range of applications using batteries - li-ion, li-poly and lead acid, in the voltage range of 18V to 60V High operating efficiency of 92% at 24VDC and 90% at 48VDC High power density solution (40 x 48 x 20 mm) aids to optimize the form-factor of end equipment platforms Dual output: 12V/3A and 12V_ISO/1.0A with tight load regulation of < ± 1% and cross regulation < ± 3% Robust supply protected for output short circuit, over load and input under voltage lockout

Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-01141 TI design provides a reference solution for ±100A shunt-based, high-side continuous bi-directional current measurement addressing applications such as battery current monitoring and current monitoring in UPS, Telecom Rectifiers and Server PSUs. This design achieves high accuracy with low shunt resistance value thus reducing power loss and hence shunt sizing.
Возможности:

Shunt-based ±100A continuous bi-directional current measurement solution for accurate current monitoring applications Tight DC accuracy of <1% across temperatures from 25ЛљC to 85ЛљC Low shunt value offers reduced power loss and enhances the system efficiency High-side current sense solution for batteries ranging from 6V to 60V (12V/24V/36V/48V) and common mode voltage up to 80V Adaptable for current sensing even close to fast switching nodes without any external common-mode filtering Fast (<10us) over-current fault alert in either direction for system safety, with programmable threshold

Документация:
  • Схемотехника
  • BOM
Описание:
The USB Type-C™ and Power Delivery (PD) minidock evaluation module (EVM) provides a complete reference solution for a USB Type-C dock including audio, USB data, power, and video. The EVM has a small 2 inch by 4 inch form factor and supports both source and sink power capabilities over the primary USB Type-C PD port. Video output capabilities include both DisplayPort and HDMI.
Возможности:

DisplayPort™ to HDMI Bi-Directional Power Capabilities DRP Full-Featured USB-C & PD Port Dual Video (up to 4K) via HDMI or miniDP Flash Update over Type-C

Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The TIDA-01369 reference design is a power supply designed for providing power to lock-step dual-core microcontrollers (MCUs) with functional safety architectures, regulating down from an automotive battery or industrial DC supply in a single stage. MCUs from multiple vendors are supported by the design. The core and I/O rails for the MCU are supervised; if a fault condition occurs, the MCU is disabled by hardware RESET output signals and the latching fault condition is reported to the MCU after normal operation is resumed. The reference design emphasizes the complementary features of three products from TI: the TPS653850-Q1 power management IC (PMIC), the TPS57160-Q1 asynchronous DC-DC buck converter, and the TPS3700-Q1 overvoltage and undervoltage supervisor.
Возможности:

Supports Power and Sequencing Requirements of Various Lock-Step Dual Core MCUs Low-Voltage MCU Core Rail with 3% Voltage Ripple from 5-mA to 1.5-A Load Optimized for Hercules TMS570xxxxx Product Family Supervisor and Reset Signals for MCU with Latching Fault Condition Operates over a Wide VIN from 2.6V to 36V (Ideal for Automotive Battery or Industrial Supplies)

Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-01444 reference design for server PSU, PC PSU, and other step-down converter applications implements a 180-W buck, dual-channel DC-DC converter with a regulatory 12-V DC input voltage designed to provide the terminal load voltage with greater than 97% efficiency and good thermal performance. The switching frequency synchronization between the dual channels is easily realized. The true differential remote sense of the dual outputs compensates the line voltage drop providing more accurate voltage for the terminal load. For improved high power density and a low profile, this integrated circuit reference design uses a planar inductor to replace the traditional discrete inductor. This TI Design has complete protection and temperature sense functions.
Возможности:

180W dual output buck converter Efficiency: 96% (typ) at 180W load; 97% (typ) at 83W load Switching frequency synchronization between dual-channel Differential remote sensing for both output channels Planner inductor as output inductor Compact form factor (47mm x 59mm) for compatible with server PSU application

Документация:
  • Схемотехника
  • BOM
  • Топология платы

Сравнение позиций

  • ()